01 / CONNECT
Connect power and Ethernet
- Set the miner on a stable, dry surface with clear space at both ends for airflow. Leave the PSU switched off and unplugged while making connections.
- Connect Ethernet from the port above the hash boards to a LAN port on your router or switch.
- Connect PCIe power to all six 6-pin sockets, two per hash board. With a PCIe 6+2 plug, seat the 6-pin section and leave the extra two pins aside. Each latch should click into place without force.
- If you bought the VMG750 kit, use its matched modular PCIe cables and supplied splitters to reach the six sockets. Fit the supplied jumper to the free end of the PSU’s 24-pin ATX cable so the PSU can start without a motherboard.
- After checking the connections, plug the PSU into a grounded outlet using a cord rated for your outlet and PSU, then switch it on. The kit’s included North American cord is for standard grounded 120 V US and Canadian outlets. Check that the miner fan is spinning and airflow is clear.
02 / SIGN IN
Open the BaikalMiner dashboard
- Allow a few minutes for startup. On your router, open the connected-devices or DHCP client list and look for the miner’s new wired connection. If you have several miners, power them up one at a time to identify their addresses.
- From a computer on the same private LAN, enter the assigned IP address in your browser’s address bar with
http://in front. The local dashboard is labeled BaikalMiner. - When prompted, enter the default web interface password
baikal. If that password fails, contact support with your unit label and order number.
Keep the legacy HTTP dashboard on your trusted local network. Leave router port forwarding disabled for the miner.
03 / CONFIGURE
Set your mining endpoint
For Bitcoin BLAKE2b (XBT), get an endpoint that explicitly supports XBT and the BK-B’s BLAKE2b mining protocol. Use the pool’s connection instructions or the mining endpoint provided by your gateway. The dashboard’s Sia algorithm label refers to the BLAKE2b mode. The endpoint determines which work the miner receives.
- Open the Miner tab and select Add Pool to create an entry.
- Enter the Pool URL exactly as supplied, including the protocol and port. Enter the Pool Worker and Pool Password in the formats required by your provider. The worker field may be a payout address or an account and worker name. Keep wallet recovery words and private keys out of these fields.
- Choose Sia under Algo for BLAKE2b. Check your payout details and remove any old entries you don’t intend to use. Select Save Pool and give the miner a few minutes to reconnect.
04 / VERIFY
Look for accepted shares
Click BaikalMiner to return to the dashboard. Check these readings once the miner has had time to start hashing.
- Devices
- Look for three devices, one per hash board, with temperatures and nonzero average hashrate.
- Pools
- Find your configured endpoint. Look for Alive under Status and true under Active. The Acc count should increase as shares are accepted.
- Provider dashboard
- If available, check that your worker or payout address is credited with shares. Reporting can lag behind the miner’s dashboard.
Share timing varies with difficulty. Give the average hashrate time to settle and use your exact unit’s listing for its recorded benchmark.
05 / MONITOR
Check cooling
On units with SPECTRE WORKS sgminer enhancements v0.3.4, check the Cooling panel on the dashboard. For first setup, use Automatic and confirm that board temperatures are updating. If the unit is in Manual mode, Restore Automatic changes the running mode. Use Save for restart with Automatic selected to keep it after a restart.
The acknowledged fan percentage is a command to the fan. Check physical airflow as well. If the fan stops or the miner reports a persistent cooling fault, switch off and unplug the PSU and contact support.
HELP / COMMON QUESTIONS
When something doesn’t look right
The dashboard won’t open
Check the Ethernet cable and the router’s wired connection list. Confirm your computer is on the same private network and recheck the miner’s IP address. A router can assign a different address after restart.
One or more hash boards are missing
Switch off and unplug the PSU. Check that all six PCIe connectors are fully seated before trying again. If a board is still missing, contact support.
The pool is down or shares keep getting rejected
Recheck the endpoint protocol and port, worker credentials, payout address, and algorithm against your provider’s instructions. Check the provider’s service status. If the issue persists, record the exact error and how long it has been happening.
When contacting support, include your unit label, order number, PSU model, and the dashboard status or error. Remove passwords and private details from screenshots.
